SPD Tech Circuit Protection Devices & Solutions
中文

Protection of Buildings

10 min
LPZBuilding lightning protectionGraded protection

The complete chain from roof interception to final-stage devices — SPD graded cascade as the backbone, with end-stage TVS/ESD fine clamping and PPTC/Fuse overcurrent backup, and why LPZ boundaries must match reality.

Lightning protection of a building is not "fitting some SPDs". It is a continuous chain from interception, through down-conduction and earthing, to internal equipotential bonding. The SPD is the last link, not the whole system.

1. What LPZ zoning means in practice

The LPZ (Lightning Protection Zone) divides a building by lightning electromagnetic field strength:

Zone Location Field strength Corresponding measures
LPZ 0 Outside the building Strongest External lightning protection (air-termination, down-conductors, earth electrodes)
LPZ 1 At the building incomer Strong Type 1 SPD
LPZ 2 Distribution panels, rooms Moderate Type 2 SPD
LPZ 3 At the equipment Weak Type 3 SPD, equipment shielding, equipotential bonding

The key insight: LPZ boundaries are not defined by where the drawing puts them — they are defined by the shielding and equipotential measures actually implemented. A wall with no shielding or bonding is not a boundary; both sides of it are in the same LPZ.

This has an important corollary: LPZ zoning must match the construction as built. If a partition is designated LPZ 2 on the drawings but the shielding and bonding were never installed, the equipment in that room is physically still in an LPZ 1 field. A common and expensive failure: the SPD grading was designed against a zoning that does not exist on site.

1. Interception

Air-termination rods, catenary wires, or a mesh, delivering the current to designated down-conductors.

  • Sphere method: the rolling sphere radius is set by building height (h ≤ 30 m uses 45 m; 30–120 m uses 150 m, and so on). The volume swept by the sphere is not protected.
  • Rooftop equipment: air-conditioning condensers, antennas, solar water heaters, and rooftop PV all project above the roof and need their own interception and down-conductor. They cannot be assumed to be covered by the roof mesh.

Rooftop PV is a common weak point

PV module frames and backplanes form large-area metal. If a module is struck, current looks for a path. If the frames are not bonded, or the down-conductor is undersized, or the connection to PE is missing, the current passes through the module or the mounting structure and destroys them. This is the most common PV lightning damage morphology.

2. Down-conduction

Moving the current safely to the earth electrode.

  • Cross-section: ≥ 50 mm² copper (equivalent to 35 mm² aluminium); exposed external down-conductors should not fall below 35 mm² copper
  • Routing: avoid sharp bends (tight radii cause corona and local discharge)
  • Separate structural reinforcement: acceptable if reliably welded and of adequate cross-section, but any combination of the two must be detailed so the connections never become the bottleneck

3. Earthing

Dissipating the current into the earth.

  • A ring earth electrode (closed loop) is effective at suppressing earth potential rise
  • Types: vertical rods (deep wells), horizontal radials, ring networks
  • The meaningful metric is not "how many ohms" but how uniform the potential distribution across the grid is — uniform means small voltage differences between devices, i.e. low common-mode voltage

4. Internal equipotential bonding and SPDs

The final link, inside the building.

  • Equipotential bonding: connect all systems requiring protection into one equipotential body
  • SPD grading: Type 1 at LPZ 0/1, Type 2 at 1/2, Type 3 at 2/3
  • Shielding and segregation: separate power and signal routes, avoid long parallel runs, shield critical lines

3. Why a single stage is not enough

A widespread design misconception: "we fitted a Type 1 at the incomer, so the building is protected."

What actually happens: the Type 1 limits the surge current, but leaves a residual Up of several hundred volts, potentially over 1 kV. This voltage propagates through the internal distribution, where line inductance, capacitance and spatial induction add to it. By the time it reaches the far end, it may be higher than it was at the Type 1.

To put it visually: the Type 1 stops the flood, but the water still arrives downstream with several hundred volts of head. The equipment is still standing in it.

Hence the full approach: an incomer stage dumping bulk energy, an internal stage sharing the load and reducing residual voltage, and a device-side stage clamping precisely.

4. Retrofitting existing buildings

Difficulty Response
No reliable earth grid can be built Assess what exists, add vertical earth electrodes if needed; prioritise equipotential bonding (cheap, fast, effective)
Power and signal cabling already intermixed Replace critical signal runs with shielded cable and bond them; at minimum add final-stage protection to critical equipment
No panel space for adequate stage separation Use hybrid single-stage SPDs, or integrated solutions with isolation
No earth testing capability At minimum perform earth continuity and equipotential bonding continuity tests — more meaningful than a resistance figure
Limited shutdown windows Work zone by zone and cabinet by cabinet; use mobile protection or temporary measures for critical loads

Recommended priority for retrofit projects: 1. Equipotential bonding (cheapest, fastest, most effective) 2. Final-stage Type 3 at critical equipment (targets the actual failures) 3. Type 1/Type 2 at the incomer (broad improvement) 4. Earth grid reconstruction (largest investment, do it when conditions allow)

5. A self-assessment

If any of the following apply, the lightning protection is almost certainly incomplete:

  • [ ] Only one SPD stage at the incomer; nothing at the equipment end
  • [ ] Rooftop equipment (PV, air-conditioning, antennas) without dedicated interception and down-conductors
  • [ ] No systematic equipotential bonding
  • [ ] No surge protection on communication or signal lines
  • [ ] As-built construction differs from the lightning protection drawings
  • [ ] SPD counter readings have never been recorded