Thermal & Inrush Protection
Covering turn-on inrush limiting (Inrush NTC/PTC) and thermal protection (TMOV thermal disconnect, PTC reset), with selection guidance and pitfalls.
What this covers
Thermal protection & inrush limiting: NTC / PTC / TMOV overlap.
To textNTC vs PTC limiting
NTC suppresses inrush (low-R hot); PTC resets (R jumps on heating).
To textMOV to TMOV
MOV short-fails; TMOV adds thermal disconnector, fail-safe open.
To textPTC self-reset thermal
Battery/motor overheat protection, trip 60–130 ℃.
To textParameter checklist
Trip temp, Rmin, I²t, energy, response time, temp drift.
ViewWhat This Domain Covers
Thermal and inrush protection addresses two problems:
- Turn-on inrush: the tens-of-times transient at power-on of capacitors/lamps/motors, limited by NTC / PTC inrush limiters.
- Thermal anomaly: a device overheats from overvoltage, overcurrent or aging, prevented from fire or cascading failure by thermal disconnect (TMOV) / PTC self-reset.
It overlaps with overvoltage and overcurrent protection but is independently responsible for "transient and steady-state anomalies of current/temperature."
Turn-on Inrush: NTC vs PTC
| Dimension | Inrush NTC | PTC inrush limiter |
|---|---|---|
| temp coefficient | negative (high cold → low hot) | positive (overcurrent heats → rises to limit) |
| steady loss | yes (still several Ω hot) | design-dependent |
| typical use | PSU/LED/inverter start | motor start, resettable limit |
| frequent switching | hot = no limiting, needs relay bypass | self-resets |
NTC selection: R25 ≈ Vpeak / Iinrush_target − line resistance; steady current must be below rating or it overheats, loses limiting and overheats itself.
Key reminder
An NTC stays hot and low-resistance after a fault, so frequent switching defeats its limiting. For high reliability use "NTC + relay bypass" or an active limiter.
Thermal Protection: From MOV to TMOV
A plain MOV can short after aging → continuous heating → fire, one of the biggest hazards in mains equipment. Solutions:
- TMOV: built-in thermal disconnect opens permanently at abnormal temperature and signals failure—safe failure.
- External thermal fuse: a thermal fuse bonded to the MOV.
- System-level over-temperature protection (required by IEC 62368-1): monitor and cut overall.
Selection: prefer TMOV for any mains MOV; use the fault indicator in alarm or forced-shutdown logic.
PTC Self-Reset Thermal Protection
A PPTC is essentially temperature-triggered: overcurrent → heat → PTC effect → high-resistance limiting, resets on cooling. In battery secondary protection, motor stall and port overcurrent it delivers both overcurrent and overheat protection.
Parameter Checklist
- [ ] turn-on inrush current → NTC R25 / PTC rating
- [ ] steady current → exceeds NTC rating (self-heating)?
- [ ] efficiency-sensitive → need relay bypass for NTC?
- [ ] mains MOV → switch to TMOV (fire safety)?
- [ ] fault indicator → wired to system alarm?
- [ ] frequent switching → need active limiter instead of NTC?
Next
- Device library: Inrush NTC & PTC · TMOV · PPTC
- Read Overvoltage selection & coordination and Overcurrent selection
What This Domain Covers
Thermal and inrush protection addresses two problems:
- Turn-on inrush: the tens-of-times transient at power-on of capacitors/lamps/motors, limited by NTC / PTC inrush limiters.
- Thermal anomaly: a device overheats from overvoltage, overcurrent or aging, prevented from fire or cascading failure by thermal disconnect (TMOV) / PTC self-reset.
It overlaps with overvoltage and overcurrent protection but is independently responsible for "transient and steady-state anomalies of current/temperature."
Turn-on Inrush: NTC vs PTC
| Dimension | Inrush NTC | PTC inrush limiter |
|---|---|---|
| temp coefficient | negative (high cold → low hot) | positive (overcurrent heats → rises to limit) |
| steady loss | yes (still several Ω hot) | design-dependent |
| typical use | PSU/LED/inverter start | motor start, resettable limit |
| frequent switching | hot = no limiting, needs relay bypass | self-resets |
NTC selection: R25 ≈ Vpeak / Iinrush_target − line resistance; steady current must be below rating or it overheats, loses limiting and overheats itself.
Key reminder
An NTC stays hot and low-resistance after a fault, so frequent switching defeats its limiting. For high reliability use "NTC + relay bypass" or an active limiter.
Thermal Protection: From MOV to TMOV
A plain MOV can short after aging → continuous heating → fire, one of the biggest hazards in mains equipment. Solutions:
- TMOV: built-in thermal disconnect opens permanently at abnormal temperature and signals failure—safe failure.
- External thermal fuse: a thermal fuse bonded to the MOV.
- System-level over-temperature protection (required by IEC 62368-1): monitor and cut overall.
Selection: prefer TMOV for any mains MOV; use the fault indicator in alarm or forced-shutdown logic.
PTC Self-Reset Thermal Protection
A PPTC is essentially temperature-triggered: overcurrent → heat → PTC effect → high-resistance limiting, resets on cooling. In battery secondary protection, motor stall and port overcurrent it delivers both overcurrent and overheat protection.
Parameter Checklist
- [ ] turn-on inrush current → NTC R25 / PTC rating
- [ ] steady current → exceeds NTC rating (self-heating)?
- [ ] efficiency-sensitive → need relay bypass for NTC?
- [ ] mains MOV → switch to TMOV (fire safety)?
- [ ] fault indicator → wired to system alarm?
- [ ] frequent switching → need active limiter instead of NTC?
Next
- Device library: Inrush NTC & PTC · TMOV · PPTC
- Read Overvoltage selection & coordination and Overcurrent selection
